GRILL GUARD JEEP GRAND CHEROKEE

Grill Guard Jeep Grand Cherokee-PDF Download

  • Date:21 May 2020
  • Views:11
  • Downloads:0
  • Pages:7
  • Size:1.03 MB

Share Pdf : Grill Guard Jeep Grand Cherokee

Download and Preview : Grill Guard Jeep Grand Cherokee


Report CopyRight/DMCA Form For : Grill Guard Jeep Grand Cherokee


Description:

bumper cover and radiator support to access and remove block offs Fig 9 2014 driver side pictured GRILLE GUARD 2011 16 JEEP GRAND CHEROKEE Page 6 of 7 9 27 13 DP Driver Side Installation Pictured Fig 13 Fig 11B Rotate the Bracket to meet the mounting holes for the tow hooks Fig 12 2 10mm x 35mm Hex Bolts 2 10mm Lock Washers 2 10mm x 27mm Large Flat Washers Front 3 12mm x 35mm

Transcription:

GRILLE GUARD,2011 16 JEEP GRAND CHEROKEE,PARTS LIST. 1 Grille Guard 2 10 1 5mm x 30mm Button Head Bolts. 1 Driver Left Side Mounting Bracket 4 10 1 5mm x 35mm Hex Bolts. 1 Passenger Right Side Mounting Bracket 4 10mm x 27mm OD x 3mm Large Flat Washers. 1 Driver Left Side Top Bracket 4 10mm x 20mm OD x 2 5mm Small Flat Washers. 1 Passenger Right Side Top Bracket 4 10mm Lock Washers. 6 12 1 75mm x 35mm Hex Bolts 2 10mm Nylon Lock Nuts. 12 12mm x 32mm OD x 3mm Flat Washers 4 6mm x 18mm OD x 1 6mm Flat Washers. 6 12mm Lock Washers 1 50mm x 400mm Adhesive backed Foam Tape. 6 12mm Hex Nuts,Passenger Right Driver Left Side,Side Top Bracket Top Bracket. Driver Left Side,Frame Mounting,Passenger Right Bracket. Side Frame,Mounting Bracket, NOTICE Grille Guard may interfere with the performance of forward facing cameras and. sensors if equipped, 1 REMOVE CONTENTS FROM BOX VERIFY ALL PARTS ARE PRESENT READ INSTRUCTIONS.
CAREFULLY BEFORE STARTING INSTALLATION ASSISTANCE IS HIGHLY RECOMMENDED. IMPORTANT This Grille Guard may not be compatible with optional Adaptive Cruise. Control Forward Collision Warning Systems featuring grille mounted laser control sensor. 2 Determine if the vehicle is equipped with or without factory tow hooks Figure 1 Remove the plastic. splash guard under the front bumper cover Figure 2. Vehicles with factory tow hooks Remove both tow hooks if equipped and proceed to Step 3. NOTE Tow hooks cannot be reinstalled with the Grille Guard. Vehicles without factory tow hooks, a 2011 13 Remove the factory hardware securing the ends of the bumper cover Release the. clips at the ends of the plastic bumper cover that attach the lower cover to the upper cover. Figure 3 NOTE It is not necessary to remove the lower bumper cover only release the clips. at both ends of the cover Next remove the 3 clips fastening the air deflector to the bottom of. the crossmember Figure 4 Carefully pull the bumper cover forward for access and pull the air. deflector out from behind the bumper cover Figure 5A Release the 2 clips and remove the. block off cover at each end of the air deflector Figure 5B Reinstall the air deflector without. block offs and bumper cover using the factory hardware. b 2014 Models The block offs covering the openings in the bumper are clipped onto the back of. the bumper cover only Figure 6 Remove the hardware at the bottom of the inner fender. panel Figure 7 Reach up behind the bumper to release the clips and remove the block off. from each opening in the bumper cover Figures 8 9 No other disassembly is required. Page 2 of 7 9 27 13 DP,GRILLE GUARD,2011 16 JEEP GRAND CHEROKEE. 3 Locate the 2 threaded holes in the bottom of the frame channel Figure10 Select the driver side. Frame Mounting Bracket Hold the Bracket with the mounting tab flat Figure11A insert it through the. opening and rotate up into position in line with the factory threaded holes Figure11B Bolt the. Bracket to the frame channel with 2 10mm x 30mm Hex Bolts 2 10mm Large Flat Washers and 2. 10mm Lock Washers Figure 12 Snug but do not fully tighten the hardware at this time Repeat this. step for passenger side Frame Bracket installation. 4 With assistance hold the Grille Guard up to the outside of the Mounting Brackets Attach the Grille. Guard to the Mounting Brackets with the included 6 12mm x 35mm Hex Bolts 12 12mm Flat. Washers 6 12mm Lock Washers and 6 12mm Hex Nuts Figure 13 WARNING Do not allow. Grille Guard to come in contact with the vehicle Temporarily tighten hardware at this time to hold the. Grille Guard in position, 5 Open the front hood Locate and remove the factory 6mm hex bolt on the driver side securing the. plastic cover to the radiator support Figure 14 Use the included 2 6mm Flat Washers as spacers to. fit into the recess in the plastic cover Select the driver side Top Bracket Apply a layer of Adhesive. backed Foam Tape to the bottom of the Top Bracket to protect the plastic cover Figures 15A 15B. Place the Top Bracket on top of the washers and bolt it to the radiator support using the factory hex bolt. Figure 16 NOTE For proper fit the Top Brackets must fit as close to the plastic cover and the top of. the grille as possible for hood closure, 6 Line up the mounting hole in the Top Bracket with the hole in the Grille Guard upright Bolt the Bracket. to the Grille Guard with 1 10mm x 30mm Button Head Bolt 2 10mm x 20mm Small Flat Washers. and 1 10mm Nylon Lock Nut Figures 16 17 Do not tighten hardware at this time. 7 Repeat Steps 5 6 for passenger side Top Bracket installation. 8 Align and adjust the Grille Guard and tighten all hardware. 9 VERY IMPORTANT Slowly close the hood to check for clearance between the hood and the Top. Brackets Adjust the Top Brackets as necessary for proper hood closure. 10 Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment wax this product after installing Regular waxing is recommended to add a protective layer. over the finish Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel Aluminum polish may be used to polish small scratches and scuffs on the finish Mild soap may be. used also to clean the Grille Guard, For gloss black finishes Mild soap may be used to clean the Grille Guard.
Driver Side Installation Pictured, Driver side opening in grille Remove splash guard under front bumper. for tow hook if equipped,Fig 1 Fig 2, For vehicles with factory tow hooks proceed to Figure 6. Page 3 of 7 9 27 13 DP,GRILLE GUARD,2011 16 JEEP GRAND CHEROKEE. Driver Side Installation Pictured, 2011 13 vehicles Remove factory hardware and release. clips at ends of lower bumper cover only Do not,remove lower bumper cover For vehicles without.
factory tow hooks only,Remove 3 factory clips to,release the inner air deflector. Fig 4 Pull,Carefully pull bumper cover forward,and remove inner air deflector. Fig 5A 2011 13 Models Inner air deflector,assembly applies to vehicles without tow hooks. Remove 2 factory clips to remove the block,off cover from each end of the air deflector. 2011 13 driver side of air deflector pictured,Fig 6 2014 driver side pictured.
Page 4 of 7 9 27 13 DP,GRILLE GUARD,2011 16 JEEP GRAND CHEROKEE. Driver Side Installation Pictured,Fig 7 2014 driver side pictured from. behind bumper Remove factory,hardware to access mounting location. Fig 10 on bottom of frame channel,Fig 8 2014 driver side pictured from below. front bumper Carefully pull the air dam,slightly forward and reach up between.
bumper cover and radiator support to access,and remove block offs. Fig 9 2014 driver side pictured,Fig 10 Driver side mounting location. pictured from below and behind bumper,Page 5 of 7 9 27 13 DP. GRILLE GUARD,2011 16 JEEP GRAND CHEROKEE,Driver Side Installation Pictured. Fig 11A Slide the Bracket into the tow hook opening. Fig 11B Rotate the Bracket to meet the,mounting holes for the tow hooks.
2 10mm x 35mm Hex Bolts,2 10mm Lock Washers,2 10mm x 27mm Large Flat Washers. 3 12mm x 35mm Hex Bolts,3 12mm Lock Washers,6 12mm Flat Washers. 3 12mm Hex Nuts,Page 6 of 7 9 27 13 DP,GRILLE GUARD. 2011 16 JEEP GRAND CHEROKEE,Driver Side Installation Pictured. 2 6mm Flat Washers,Fig 15B Adhesive backed,Apply Adhesive backed Foam Tape.
to bottom of both Top Brackets,Factory hex bolt,Fig 15A Driver Side Top Bracket Pictured. 10mm x 30mm Button Head Bolt,2 10mm x 20mm Small Flat Washers. 10mm Nylon Lock Nut,Fig 16 Front,Complete Installation.

Related Books